meshcore-open/documentation/ble-protocol.md

BLE Protocol & Data Layer

This is a technical reference for the communication protocol and data architecture.

Transport Layer

The app supports three transports, all sharing the same command/response protocol:

Transport	Method	Implementation
Bluetooth LE	Nordic UART Service (NUS) GATT	flutter_blue_plus
USB Serial	Packet-framed serial	MeshCoreUsbManager
TCP	Packet-framed socket	MeshCoreTcpConnector

BLE (Nordic UART Service)

• Service UUID: 6e400001-b5a3-f393-e0a9-e50e24dcca9e
• RX Characteristic (write to device): 6e400002-b5a3-f393-e0a9-e50e24dcca9e
• TX Characteristic (notify from device): 6e400003-b5a3-f393-e0a9-e50e24dcca9e

Raw Uint8List payloads are written directly to the RX characteristic. Writes use "write without response" if supported, falling back to "write with response".

USB and TCP Framing

Both use a lightweight packet framing codec:

TX (host → device):  [0x3C][len_lo][len_hi][payload...]
RX (device → host):  [0x3E][len_lo][len_hi][payload...]

• Frame start: 0x3C (<) for outgoing, 0x3E (>) for incoming
• Length: 2-byte little-endian, payload only
• Max payload: 172 bytes
• TCP: tcpNoDelay: true (Nagle disabled), writes serialized to prevent interleaving
• USB: 10ms post-write delay between frames

Connection State Machine

enum MeshCoreConnectionState {
  disconnected,
  scanning,
  connecting,
  connected,
  disconnecting,
}

BLE Connection Lifecycle

1. Scan with known name prefixes (defined in MeshCoreUuids.deviceNamePrefixes):
   • MeshCore-
   • Whisper-
   • WisCore-
   • HT-
   • LowMesh_MC_
2. Connect with 15-second timeout
3. Request MTU 185 bytes (non-web only)
4. Discover services and locate NUS
5. Enable TX notifications (up to 3 attempts on native)
6. Subscribe to TX characteristic for incoming frames
7. Initial sync: device info query, time sync, channel sync

Auto-Reconnect (BLE Only)

On unexpected disconnection, auto-reconnect with exponential backoff:

• Delays: 1s, 2s, 4s, 8s, 16s, 30s, 30s...
• Resets on successful connection
• Disabled for manual disconnects
• Not available for USB or TCP

Protocol Constants

Constant	Value	Description
Max frame size	172 bytes	BLE/USB/TCP payload limit
Public key size	32 bytes	Ed25519 public key
Max path size	64 bytes	Maximum path data
Max name size	32 bytes	Maximum node name
Max text payload	160 bytes	Firmware MAX_TEXT_LEN
App protocol version	3	Sent in device query
Contact frame size	148 bytes	Fixed-size contact record

Command Codes (App → Device)

Code	Name	Description
1	CMD_APP_START	Announce app connection
2	CMD_SEND_TXT_MSG	Send direct text message
3	CMD_SEND_CHANNEL_TXT_MSG	Send channel text message
4	CMD_GET_CONTACTS	Request contact list
5	CMD_GET_DEVICE_TIME	Query device clock
6	CMD_SET_DEVICE_TIME	Set device clock
7	CMD_SEND_SELF_ADVERT	Broadcast own advertisement
8	CMD_SET_ADVERT_NAME	Set node name
9	CMD_ADD_UPDATE_CONTACT	Add or update a contact
10	CMD_SYNC_NEXT_MESSAGE	Request next queued message
11	CMD_SET_RADIO_PARAMS	Set radio parameters
12	CMD_SET_RADIO_TX_POWER	Set TX power
13	CMD_RESET_PATH	Reset contact path
14	CMD_SET_ADVERT_LATLON	Set advertised location
15	CMD_REMOVE_CONTACT	Remove a contact
16	CMD_SHARE_CONTACT	Share contact to mesh
17	CMD_EXPORT_CONTACT	Export contact as bytes
18	CMD_IMPORT_CONTACT	Import contact from bytes
19	CMD_REBOOT	Reboot device
20	CMD_GET_BATT_AND_STORAGE	Query battery and storage
22	CMD_DEVICE_QUERY	Query device info
26	CMD_SEND_LOGIN	Login to repeater/room
27	CMD_SEND_STATUS_REQ	Request repeater status
30	CMD_GET_CONTACT_BY_KEY	Get contact by public key
31	CMD_GET_CHANNEL	Get channel definition
32	CMD_SET_CHANNEL	Set channel name and PSK
36	CMD_SEND_TRACE_PATH	Request path trace
38	CMD_SET_OTHER_PARAMS	Set misc parameters
39	CMD_GET_TELEMETRY_REQ	Request sensor telemetry
40	CMD_GET_CUSTOM_VAR	Get custom variables
41	CMD_SET_CUSTOM_VAR	Set a custom variable
50	CMD_SEND_BINARY_REQ	Send binary request
57	CMD_SEND_ANON_REQ	Send anonymous request
58	CMD_SET_AUTO_ADD_CONFIG	Set auto-add configuration
59	CMD_GET_AUTO_ADD_CONFIG	Get auto-add configuration

Response / Push Codes (Device → App)

Code	Name	Description
0	RESP_CODE_OK	Generic success
1	RESP_CODE_ERR	Generic error
2	RESP_CODE_CONTACTS_START	Contact list begins
3	RESP_CODE_CONTACT	Single contact data
4	RESP_CODE_END_OF_CONTACTS	Contact list complete
5	RESP_CODE_SELF_INFO	Device self-info response
6	RESP_CODE_SENT	Message transmitted; carries [1]=is_flood, [2–5]=ack_hash, [6–9]=estimated_timeout_ms
7	RESP_CODE_CONTACT_MSG_RECV	Incoming direct message (v2)
8	RESP_CODE_CHANNEL_MSG_RECV	Incoming channel message (v2)
10	RESP_CODE_NO_MORE_MESSAGES	No more queued messages
11	RESP_CODE_EXPORT_CONTACT	Exported contact data
9	RESP_CODE_CURR_TIME	Current device time
12	RESP_CODE_BATT_AND_STORAGE	Battery mV (uint16 LE) + storage used/total (uint32 LE each)
13	RESP_CODE_DEVICE_INFO	Firmware info
16	RESP_CODE_CONTACT_MSG_RECV_V3	Incoming direct message (v3)
17	RESP_CODE_CHANNEL_MSG_RECV_V3	Incoming channel message (v3)
18	RESP_CODE_CHANNEL_INFO	Channel definition
21	RESP_CODE_CUSTOM_VARS	Custom variables
25	RESP_CODE_AUTO_ADD_CONFIG	Auto-add flags
0x80	PUSH_CODE_ADVERT	Known contact re-seen
0x81	PUSH_CODE_PATH_UPDATED	Better path found; carries the 32-byte public key of the updated contact
0x82	PUSH_CODE_SEND_CONFIRMED	Delivery ACK from remote; carries ACK hash (4 bytes) + trip time (4 bytes)
0x83	PUSH_CODE_MSG_WAITING	Offline messages queued
0x85	PUSH_CODE_LOGIN_SUCCESS	Repeater/room login succeeded
0x86	PUSH_CODE_LOGIN_FAIL	Repeater/room login failed
0x87	PUSH_CODE_STATUS_RESPONSE	Repeater status response
0x88	PUSH_CODE_LOG_RX_DATA	Radio RX data with SNR (int8, units 1/4 dB), RSSI, and raw radio packet
0x89	PUSH_CODE_TRACE_DATA	Path trace result
0x8A	PUSH_CODE_NEW_ADVERT	New node discovered
0x8B	PUSH_CODE_TELEMETRY_RESPONSE	Sensor telemetry data
0x8C	PUSH_CODE_BINARY_RESPONSE	Binary data response

Data Models

Contact

32-byte public key (primary identity), name, type (chat/repeater/room/sensor), flags, path data, GPS coordinates, last-seen timestamp. Parsed from 148-byte firmware frames with this layout:

[0]     = resp_code
[1–32]  = public key (32 bytes)
[33]    = type (1=chat, 2=repeater, 3=room, 4=sensor)
[34]    = flags (bit 0 = favorite)
[35]    = path_length
[36–99] = path (64 bytes)
[100–131] = name (32 bytes, null-padded)
[132–135] = timestamp (uint32 LE)
[136–139] = latitude (int32 LE, × 1e-6 degrees)
[140–143] = longitude (int32 LE, × 1e-6 degrees)
[144–147] = last_modified (uint32 LE)

Message (Direct)

Sender key, text, timestamp, outgoing flag, status (pending/sent/delivered/failed), message ID (UUID), retry count, ACK hash, trip time, path data, reactions.

Channel Message

Sender name, text, timestamp, status (pending/sent/failed), repeater hops, path variants, channel index, reactions, reply threading fields.

Channel

Index (0–7), name, 16-byte PSK, unread count. PSK derivation methods for hashtag (SHA-256) and community (HMAC-SHA256) channels.

Community

UUID, name, 32-byte secret, hashtag channel list. Shared via QR code.

Persistence

All data is stored via SharedPreferences (JSON-serialized). No SQLite or other database.

Data	Storage Key Pattern	Scope
Contacts	contacts<pubKey10>	Per device identity
Messages	messages_<pubKey10><contactKey>	Per device + contact
Channel Messages	channel_messages_<pubKey10><index>	Per device + channel
Channels	channels<pubKey10>	Per device identity
Channel Order	channel_order_<pubKey10>	Per device identity
Contact Groups	contact_groups<pubKey10>	Per device identity
Communities	communities_v1<pubKey10>	Per device identity
Unread Counts	contact_unread_count<pubKey10>	Per device identity
Discovered Contacts	discovered_contacts	Global
App Settings	app_settings	Global
Path History	path_history_<contactKey>	Per contact

Auto-Add Configuration Bitmask

Used by CMD_SET_AUTO_ADD_CONFIG (58) and RESP_CODE_AUTO_ADD_CONFIG (25):

Bit	Flag	Description
0	0x01	Overwrite oldest contact when list is full
1	0x02	Auto-add chat users
2	0x04	Auto-add repeaters
3	0x08	Auto-add room servers
4	0x10	Auto-add sensors

Radio Packet Payload Types

Seen inside PUSH_CODE_LOG_RX_DATA raw packets:

Code	Type
0x00	REQ (request)
0x01	RESPONSE
0x02	TXTMSG (text message)
0x03	ACK
0x04	ADVERT
0x05	GRPTXT (group/channel text)
0x06	GRPDATA (group data)
0x07	ANONREQ (anonymous request)
0x08	PATH
0x09	TRACE
0x0A	MULTIPART
0x0B	CONTROL
0x0F	RAW_CUSTOM

State Management

Uses Flutter Provider with ChangeNotifier. The central state holder is MeshCoreConnector, which owns all in-memory collections and fires debounced (50ms) notifyListeners() to update the UI. In-memory conversations are windowed to 200 messages per contact; older messages remain on disk and are loaded on demand.

Data Flow

1. Raw frames arrive over BLE/USB/TCP
2. First byte is parsed as response/push code
3. Appropriate model factory (fromFrame()) parses the data
4. In-memory collections are updated
5. Storage stores are persisted (async)
6. notifyListeners() triggers UI rebuilds
7. Screens read current state via getters