mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-04-20 22:13:47 +00:00
e2aa33b3a0
Adds a LEDManager class (src/helpers/ui/LEDManager.h) that centralizes all LED control into one component with begin()/loop() lifecycle and per-pin active-HIGH/LOW polarity support. LED settings are exposed as custom vars (led.status, led.activity) accessible via companion radio binary protocol, CLI set/get commands, and the SensorManager settings interface. Status LED modes: off, boot-30s, slow blink (200ms/4s), always on. Activity LED modes: off, BLE only, LoRa TX only, BLE + LoRa TX. Integrated into 23 board variants, replacing scattered hardcoded digitalWrite calls in onBeforeTransmit/onAfterTransmit/powerOff.
58 lines
1.6 KiB
C++
58 lines
1.6 KiB
C++
#pragma once
|
|
|
|
#include <MeshCore.h>
|
|
#include <Arduino.h>
|
|
#include <helpers/NRF52Board.h>
|
|
#include <helpers/ui/LEDManager.h>
|
|
|
|
class SenseCapSolarBoard : public NRF52BoardDCDC {
|
|
protected:
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
void initiateShutdown(uint8_t reason) override;
|
|
#endif
|
|
|
|
public:
|
|
SenseCapSolarBoard() : NRF52Board("SENSECAP_SOLAR_OTA") {}
|
|
void begin();
|
|
|
|
void onBeforeTransmit() override {
|
|
if (ledManager) ledManager->onBeforeTransmit();
|
|
}
|
|
void onAfterTransmit() override {
|
|
if (ledManager) ledManager->onAfterTransmit();
|
|
}
|
|
|
|
uint16_t getBattMilliVolts() override {
|
|
digitalWrite(VBAT_ENABLE, LOW);
|
|
int adcvalue = 0;
|
|
analogReadResolution(12);
|
|
analogReference(AR_INTERNAL_3_0);
|
|
delay(10);
|
|
adcvalue = analogRead(BATTERY_PIN);
|
|
return (adcvalue * ADC_MULTIPLIER * AREF_VOLTAGE) / 4.096;
|
|
}
|
|
|
|
const char* getManufacturerName() const override {
|
|
return "Seeed SenseCap Solar";
|
|
}
|
|
|
|
void powerOff() override {
|
|
if (ledManager) ledManager->powerOff();
|
|
|
|
#ifdef PIN_USER_BTN
|
|
while (digitalRead(PIN_USER_BTN) == LOW);
|
|
// Keep pull-up enabled in system-off so the wake line doesn't float low.
|
|
nrf_gpio_cfg_sense_input(digitalPinToInterrupt(g_ADigitalPinMap[PIN_USER_BTN]), NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW);
|
|
#elif defined(PIN_BUTTON1)
|
|
while (digitalRead(PIN_BUTTON1) == LOW);
|
|
// Keep pull-up enabled in system-off so the wake line doesn't float low.
|
|
nrf_gpio_cfg_sense_input(digitalPinToInterrupt(g_ADigitalPinMap[PIN_BUTTON1]), NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW);
|
|
#endif
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
initiateShutdown(SHUTDOWN_REASON_USER);
|
|
#else
|
|
sd_power_system_off();
|
|
#endif
|
|
}
|
|
};
|