mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-04-20 22:13:47 +00:00
aea64e1f19
- Add #pragma once to SerialEthernetInterface.h
- Rename TCP_PORT to ETH_TCP_PORT with #ifndef guard
- Fix typos: "initalizing" → "initializing"
- Fix #elif without condition → #else for STM32 block
- Replace infinite loop on ETH init failure with halt()
- Remove heartbeat Serial.print(".") output
- Remove dead beginETH() call (ETH_ENABLED, not RAK_ETH_ENABLE)
- Comment out MESH_DEBUG and ETH_DEBUG_LOGGING build flags
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
54 lines
No EOL
1.4 KiB
C++
54 lines
No EOL
1.4 KiB
C++
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#include "RAK4631Board.h"
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values set in variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void RAK4631Board::initiateShutdown(uint8_t reason) {
|
|
// Disable LoRa module power before shutdown
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
if (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
void RAK4631Board::begin() {
|
|
NRF52BoardDCDC::begin();
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
#ifdef PIN_USER_BTN
|
|
pinMode(PIN_USER_BTN, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#ifdef PIN_USER_BTN_ANA
|
|
pinMode(PIN_USER_BTN_ANA, INPUT_PULLUP);
|
|
#endif
|
|
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
} |