LoRa iGate & Digi software − Ricardo Guzman CA2RXU

Last 10 received packets list

Time	Frame	RSSI	SNR

List refresh automatically every 15 seconds.
(Local Time is NTP-Time adjusted with your GMT Offset)

Station

Add your Ham callsign and SSID.

You can leave a comment describing your station.

In the bottom there is a field for personal note that can only be seen in WEB GUI.

Callsign - SSID

Beacon Comment

Beacon Path

Symbol

Latitude

Longitude

Personal Note

Send Status at each Boot

Status

WiFi Access

Add all Wi-Fi Networks intended to be used.

Startup Delay(To Allow Router/Modem to start WiFiAP before connection)

minutes

APRS-IS

Enter you APRS-IS server and credentials.

Enable APRS-IS connection

Gate APRS-IS Messages to RF

Gate APRS-IS Objects to RF

Server

Port

Passcode

Filter

Beaconing

Set APRS beacon attributes.

Send beacon via APRS-IS

Send beacon via RF

(Select LoRa Beacon Frequency)

Beacon Interval

minutes

APRS Position Ambiguity

Send Real-GPS Beacon (Only for Boards with GPS Modules)

Black List

Add Callsigns with space between them to Blacklist (* wildcard allowed)

Blacklist

Digipeating

Define the Digipeater mode

Repeater Mode

Eco Mode (Requires Digipeating enabled and APRS-IS connection disabled).

LoRa

Config LoRa APRS Xmitting settings.

Enable LoRa RX

Enable LoRa TX

Rx Frequency

Tx Frequency

Rx Spreading Factor

Tx Spreading Factor

Rx Coding Rate

Tx Coding Rate

Rx Signal Bandwidth

Tx Signal Bandwidth

Power

dBm

Display

OLED screen configuration.

Always On

Turn 180º

Display Timeout

seconds

Remember Station Time

minutes

Battery

Battery Monitor & Health

Max Voltage on input pin is 3.3V.

Calculate voltage divider accordingly.

Send Internal Voltage

(Send Voltage As Telemetry)

Monitor Internal Voltage Health

Internal Sleep Voltage

volts

Send External Voltage

Use External I2C Voltage Sensor

Monitor External Voltage Health

External Sleep Voltage

volts

External Voltage Pin

External Voltage divider R1

kOhm

External Voltage divider R2

kOhm

WX Telemetry

Define Wx telemetry

Activate Wx Telemetry (Requires a BME/BMP280, BME680 or Si7021 sensor).

Height Correction (Above Sea-Level)

meters

Temperature Correction

C°

Syslog

Broadcast the system log over the network.

Enable syslog

Log Beacon over TCP/IP

Server

Port

TNC

TNC and KISS configuration

Enable Serial KISS

Enable TNC server (Port 8001)

Accept own frames via KISS

Enable APRS Bridge

MQTT

Set your MQTT server

Enable

Send (also) iGate Beacon

Server

Topic (Default is aprs-igate)

Username

Password

Port (Default is 1883)

Reboot Time

Reboot Mode Active

Time before forced Reboot

hours

WiFi Auto AP

WiFi AP will start if there is no WiFi connection available. Timeout will count from startup or last client disconnected.

Password

WiFiAP timeout (to search again)

minutes

Set to 0 if you don't want WiFi AP to stop.

OTA

Set your username and password to allow firmware updating over-the-air.

Username

Password

Admin

Set your username and password to allow access to the web interface.

Web interface authentication

Username

Password

Remote Management

Manage Station via APRS Messages. Leave empty to disable!

Callsign-SSID of Managers, space separated, trailing * wildcard allowed (ex: AB1CDE-9, AB1CDE*)

Managers commands only via RF (not APRS-IS)

NTP

Set your GMT Time Zone.

NTP Server hostname

GMT Time Correction Offset

hours

Experimental

You can test new features. Use at your own risk!

When "only" iGate Mode loses WiFi, it will change into a Digipeater Mode and after 15 min check if WiFi available and return to "only" iGate Mode.

Backup Digipeater Mode