mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-04-20 22:13:47 +00:00
e2aa33b3a0
Adds a LEDManager class (src/helpers/ui/LEDManager.h) that centralizes all LED control into one component with begin()/loop() lifecycle and per-pin active-HIGH/LOW polarity support. LED settings are exposed as custom vars (led.status, led.activity) accessible via companion radio binary protocol, CLI set/get commands, and the SensorManager settings interface. Status LED modes: off, boot-30s, slow blink (200ms/4s), always on. Activity LED modes: off, BLE only, LoRa TX only, BLE + LoRa TX. Integrated into 23 board variants, replacing scattered hardcoded digitalWrite calls in onBeforeTransmit/onAfterTransmit/powerOff.
93 lines
2 KiB
C++
93 lines
2 KiB
C++
#pragma once
|
|
|
|
#include <MeshCore.h>
|
|
#include <Arduino.h>
|
|
#include <helpers/NRF52Board.h>
|
|
#include <helpers/ui/LEDManager.h>
|
|
|
|
class T1000eBoard : public NRF52BoardDCDC {
|
|
protected:
|
|
uint8_t btn_prev_state;
|
|
|
|
public:
|
|
T1000eBoard() : NRF52Board("T1000E_OTA") {}
|
|
void begin();
|
|
|
|
uint16_t getBattMilliVolts() override {
|
|
#ifdef BATTERY_PIN
|
|
#ifdef PIN_3V3_EN
|
|
digitalWrite(PIN_3V3_EN, HIGH);
|
|
#endif
|
|
analogReference(AR_INTERNAL_3_0);
|
|
analogReadResolution(12);
|
|
delay(10);
|
|
float volts = (analogRead(BATTERY_PIN) * ADC_MULTIPLIER * AREF_VOLTAGE) / 4096;
|
|
#ifdef PIN_3V3_EN
|
|
digitalWrite(PIN_3V3_EN, LOW);
|
|
#endif
|
|
|
|
analogReference(AR_DEFAULT); // put back to default
|
|
analogReadResolution(10);
|
|
|
|
return volts * 1000;
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
const char* getManufacturerName() const override {
|
|
return "Seeed Tracker T1000-E";
|
|
}
|
|
|
|
int buttonStateChanged() {
|
|
#ifdef BUTTON_PIN
|
|
uint8_t v = digitalRead(BUTTON_PIN);
|
|
if (v != btn_prev_state) {
|
|
btn_prev_state = v;
|
|
return (v == LOW) ? 1 : -1;
|
|
}
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
void powerOff() override {
|
|
#ifdef HAS_GPS
|
|
digitalWrite(GPS_VRTC_EN, LOW);
|
|
digitalWrite(GPS_RESET, LOW);
|
|
digitalWrite(GPS_SLEEP_INT, LOW);
|
|
digitalWrite(GPS_RTC_INT, LOW);
|
|
digitalWrite(GPS_EN, LOW);
|
|
#endif
|
|
|
|
#ifdef BUZZER_EN
|
|
digitalWrite(BUZZER_EN, LOW);
|
|
#endif
|
|
|
|
#ifdef PIN_3V3_EN
|
|
digitalWrite(PIN_3V3_EN, LOW);
|
|
#endif
|
|
|
|
#ifdef PIN_3V3_ACC_EN
|
|
digitalWrite(PIN_3V3_ACC_EN, LOW);
|
|
#endif
|
|
#ifdef SENSOR_EN
|
|
digitalWrite(SENSOR_EN, LOW);
|
|
#endif
|
|
|
|
// set led on and wait for button release before poweroff
|
|
#ifdef LED_PIN
|
|
digitalWrite(LED_PIN, HIGH);
|
|
#endif
|
|
#ifdef BUTTON_PIN
|
|
while(digitalRead(BUTTON_PIN));
|
|
#endif
|
|
|
|
if (ledManager) ledManager->powerOff();
|
|
|
|
#ifdef BUTTON_PIN
|
|
nrf_gpio_cfg_sense_input(BUTTON_PIN, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_HIGH);
|
|
#endif
|
|
|
|
sd_power_system_off();
|
|
}
|
|
};
|