mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-04-20 22:13:47 +00:00
bed311313a
Adds a new variant 'ikoka_stick_nrf' and associated support files. This is based on the Xiao nRF54 code with pin numbers and functions changed to suit the differences in hardware between the WIO SX1262 board and the Ikoka Stick. Sets the default LoRa transmit power to 9dBm to avoid burning up the frontend in Ikoka Sticks equipped with the Ebyte 33dBm S22 module on first boot. Adds support for an SSD1306 display connected to the display header. Note the display pinout is the same as the RAK4631 display header so make sure to use a display wired accordingly (aliexpress etc. SSD1306s typically have Vcc & GND reversed from what this board expects). Adds support for display rotation to SSD1306Display via a platformIO define. This support was added following the same paradigms found elsewhere in the code for rotating a display.
86 lines
2.4 KiB
C++
86 lines
2.4 KiB
C++
#include "variant.h"
|
|
#include "wiring_constants.h"
|
|
#include "wiring_digital.h"
|
|
#include "nrf.h"
|
|
|
|
const uint32_t g_ADigitalPinMap[] =
|
|
{
|
|
// D0 .. D10
|
|
2, // D0 is P0.02 (A0)
|
|
3, // D1 is P0.03 (A1)
|
|
28, // D2 is P0.28 (A2)
|
|
29, // D3 is P0.29 (A3)
|
|
4, // D4 is P0.04 (A4,SDA)
|
|
5, // D5 is P0.05 (A5,SCL)
|
|
43, // D6 is P1.11 (TX)
|
|
44, // D7 is P1.12 (RX)
|
|
45, // D8 is P1.13 (SCK)
|
|
46, // D9 is P1.14 (MISO)
|
|
47, // D10 is P1.15 (MOSI)
|
|
|
|
// LEDs
|
|
26, // D11 is P0.26 (LED RED)
|
|
6, // D12 is P0.06 (LED BLUE)
|
|
30, // D13 is P0.30 (LED GREEN)
|
|
14, // D14 is P0.14 (READ_BAT)
|
|
|
|
// LSM6DS3TR
|
|
40, // D15 is P1.08 (6D_PWR)
|
|
27, // D16 is P0.27 (6D_I2C_SCL)
|
|
7, // D17 is P0.07 (6D_I2C_SDA)
|
|
11, // D18 is P0.11 (6D_INT1)
|
|
|
|
// MIC
|
|
42, // D19 is P1.10 (MIC_PWR)
|
|
32, // D20 is P1.00 (PDM_CLK)
|
|
16, // D21 is P0.16 (PDM_DATA)
|
|
|
|
// BQ25100
|
|
13, // D22 is P0.13 (HICHG)
|
|
17, // D23 is P0.17 (~CHG)
|
|
|
|
//
|
|
21, // D24 is P0.21 (QSPI_SCK)
|
|
25, // D25 is P0.25 (QSPI_CSN)
|
|
20, // D26 is P0.20 (QSPI_SIO_0 DI)
|
|
24, // D27 is P0.24 (QSPI_SIO_1 DO)
|
|
22, // D28 is P0.22 (QSPI_SIO_2 WP)
|
|
23, // D29 is P0.23 (QSPI_SIO_3 HOLD)
|
|
|
|
// NFC
|
|
9, // D30 is P0.09 (NFC1)
|
|
10, // D31 is P0.10 (NFC2)
|
|
|
|
// VBAT
|
|
31, // D32 is P0.31 (VBAT)
|
|
};
|
|
|
|
void initVariant()
|
|
{
|
|
// Disable reading of the BAT voltage.
|
|
// https://wiki.seeedstudio.com/XIAO_BLE#q3-what-are-the-considerations-when-using-xiao-nrf52840-sense-for-battery-charging
|
|
pinMode(VBAT_ENABLE, OUTPUT);
|
|
//digitalWrite(VBAT_ENABLE, HIGH);
|
|
// This was taken from Seeed github butis not coherent with the doc,
|
|
// VBAT_ENABLE should be kept to LOW to protect P0.14, (1500/500)*(4.2-3.3)+3.3 = 3.9V > 3.6V
|
|
// This induces a 3mA current in the resistors :( but it's better than burning the nrf
|
|
digitalWrite(VBAT_ENABLE, LOW);
|
|
|
|
// Low charging current (50mA)
|
|
// https://wiki.seeedstudio.com/XIAO_BLE#battery-charging-current
|
|
//pinMode(PIN_CHARGING_CURRENT, INPUT);
|
|
|
|
// High charging current (100mA)
|
|
pinMode(PIN_CHARGING_CURRENT, OUTPUT);
|
|
digitalWrite(PIN_CHARGING_CURRENT, LOW);
|
|
|
|
pinMode(PIN_QSPI_CS, OUTPUT);
|
|
digitalWrite(PIN_QSPI_CS, HIGH);
|
|
|
|
pinMode(LED_RED, OUTPUT);
|
|
digitalWrite(LED_RED, HIGH);
|
|
pinMode(LED_GREEN, OUTPUT);
|
|
digitalWrite(LED_GREEN, HIGH);
|
|
pinMode(LED_BLUE, OUTPUT);
|
|
digitalWrite(LED_BLUE, HIGH);
|
|
}
|