Merge pull request #724 from recrof/thinknode_m1_refactor

tidy up thinknode_m1 variant

variants/thinknode_m1/ThinkNodeM1Board.cpp

@@ -0,0 +1,95 @@
+#include "ThinkNodeM1Board.h"
+#include <Arduino.h>
+
+#ifdef THINKNODE_M1
+
+#include <Wire.h>
+#include <bluefruit.h>
+
+static BLEDfu bledfu;
+
+static void connect_callback(uint16_t conn_handle) {
+  (void)conn_handle;
+  MESH_DEBUG_PRINTLN("BLE client connected");
+}
+
+static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
+  (void)conn_handle;
+  (void)reason;
+
+  MESH_DEBUG_PRINTLN("BLE client disconnected");
+}
+
+void ThinkNodeM1Board::begin() {
+  // for future use, sub-classes SHOULD call this from their begin()
+  startup_reason = BD_STARTUP_NORMAL;
+
+  Wire.begin();
+
+#ifdef P_LORA_TX_LED
+  pinMode(P_LORA_TX_LED, OUTPUT);
+  digitalWrite(P_LORA_TX_LED, LOW);
+#endif
+
+  pinMode(SX126X_POWER_EN, OUTPUT);
+  digitalWrite(SX126X_POWER_EN, HIGH);
+  delay(10); // give sx1262 some time to power up
+}
+
+uint16_t ThinkNodeM1Board::getBattMilliVolts() {
+  int adcvalue = 0;
+
+  analogReference(AR_INTERNAL_3_0);
+  analogReadResolution(12);
+  delay(10);
+
+  // ADC range is 0..3000mV and resolution is 12-bit (0..4095)
+  adcvalue = analogRead(PIN_VBAT_READ);
+  // Convert the raw value to compensated mv, taking the resistor-
+  // divider into account (providing the actual LIPO voltage)
+  return (uint16_t)((float)adcvalue * REAL_VBAT_MV_PER_LSB);
+}
+
+bool ThinkNodeM1Board::startOTAUpdate(const char *id, char reply[]) {
+  // Config the peripheral connection with maximum bandwidth
+  // more SRAM required by SoftDevice
+  // Note: All config***() function must be called before begin()
+  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
+
+  Bluefruit.begin(1, 0);
+  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
+  Bluefruit.setTxPower(4);
+  // Set the BLE device name
+  Bluefruit.setName("THINKNODE_M1_OTA");
+
+  Bluefruit.Periph.setConnectCallback(connect_callback);
+  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
+
+  // To be consistent OTA DFU should be added first if it exists
+  bledfu.begin();
+
+  // Set up and start advertising
+  // Advertising packet
+  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+  Bluefruit.Advertising.addTxPower();
+  Bluefruit.Advertising.addName();
+
+  /* Start Advertising
+    - Enable auto advertising if disconnected
+    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
+    - Timeout for fast mode is 30 seconds
+    - Start(timeout) with timeout = 0 will advertise forever (until connected)
+
+    For recommended advertising interval
+    https://developer.apple.com/library/content/qa/qa1931/_index.html
+  */
+  Bluefruit.Advertising.restartOnDisconnect(true);
+  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
+  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
+  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds
+
+  strcpy(reply, "OK - started");
+  return true;
+}
+#endif

variants/thinknode_m1/ThinkNodeM1Board.h

@@ -0,0 +1,57 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+
+// built-ins
+#define VBAT_MV_PER_LSB   (0.73242188F)   // 3.0V ADC range and 12-bit ADC resolution = 3000mV/4096
+
+#define VBAT_DIVIDER      (0.5F)          // 150K + 150K voltage divider on VBAT
+#define VBAT_DIVIDER_COMP (2.0F)          // Compensation factor for the VBAT divider
+
+#define PIN_VBAT_READ     (4)
+#define REAL_VBAT_MV_PER_LSB (VBAT_DIVIDER_COMP * VBAT_MV_PER_LSB)
+
+class ThinkNodeM1Board : public mesh::MainBoard {
+protected:
+  uint8_t startup_reason;
+
+public:
+
+  void begin();
+  uint16_t getBattMilliVolts() override;
+  bool startOTAUpdate(const char* id, char reply[]) override;
+
+  uint8_t getStartupReason() const override {
+    return startup_reason;
+  }
+
+  #if defined(P_LORA_TX_LED)
+  void onBeforeTransmit() override {
+    digitalWrite(P_LORA_TX_LED, HIGH);   // turn TX LED on
+  }
+  void onAfterTransmit() override {
+    digitalWrite(P_LORA_TX_LED, LOW);   // turn TX LED off
+  }
+  #endif
+
+  const char* getManufacturerName() const override {
+    return "Elecrow ThinkNode-M1";
+  }
+
+  void reboot() override {
+    NVIC_SystemReset();
+  }
+
+  void powerOff() override {
+
+    // turn off all leds, sd_power_system_off will not do this for us
+    #ifdef P_LORA_TX_LED
+    digitalWrite(P_LORA_TX_LED, LOW);
+    #endif
+
+    // power off board
+    sd_power_system_off();
+
+  }
+};

variants/thinknode_m1/platformio.ini

@@ -1,33 +1,35 @@
-[nrf52840_thinknode_m1]
+[ThinkNode_M1]
 extends = nrf52_base
-platform_packages = framework-arduinoadafruitnrf52
+board = thinknode_m1
+board_build.ldscript = boards/nrf52840_s140_v6.ld
 build_flags = ${nrf52_base.build_flags}
   -I src/helpers/nrf52
   -I lib/nrf52/s140_nrf52_6.1.1_API/include
   -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52
-lib_deps =
-  ${nrf52_base.lib_deps}
-  rweather/Crypto @ ^0.4.0
-
-[ThinkNode_M1]
-extends = nrf52840_thinknode_m1
-board = thinknode_m1
-board_build.ldscript = boards/nrf52840_s140_v6.ld
-build_flags = ${nrf52840_thinknode_m1.build_flags}
   -I variants/thinknode_m1
   -D THINKNODE_M1=1
   -D RADIO_CLASS=CustomSX1262
   -D WRAPPER_CLASS=CustomSX1262Wrapper
-  -D LORA_TX_POWER=22
-  -D P_LORA_TX_LED=13
+  -D P_LORA_DIO_1=20
+  -D P_LORA_NSS=24
+  -D P_LORA_RESET=25
+  -D P_LORA_BUSY=17
+  -D P_LORA_SCLK=19
+  -D P_LORA_MISO=23
+  -D P_LORA_MOSI=22
+  -D SX126X_POWER_EN=37
+  -D SX126X_DIO2_AS_RF_SWITCH=true
+  -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
   -D SX126X_RX_BOOSTED_GAIN=1
-build_src_filter = ${nrf52840_thinknode_m1.build_src_filter}
+  -D LORA_TX_POWER=22
+  -D P_LORA_TX_LED=13
+build_src_filter = ${nrf52_base.build_src_filter}
   +<helpers/*.cpp>
-  +<helpers/nrf52/ThinkNodeM1Board.cpp>
+  +<ThinkNodeM1Board.cpp>
   +<../variants/thinknode_m1>
 lib_deps =
-  ${nrf52840_thinknode_m1.lib_deps}
+  ${nrf52_base.lib_deps}
   stevemarple/MicroNMEA @ ^2.0.6
 debug_tool = jlink
 upload_protocol = nrfutil
@@ -81,7 +83,6 @@ build_flags =
 ;  -D MESH_PACKET_LOGGING=1
 ;  -D MESH_DEBUG=1
 build_src_filter = ${ThinkNode_M1.build_src_filter}
-  +<helpers/nrf52/ThinkNodeM1.cpp>
   +<helpers/nrf52/SerialBLEInterface.cpp>
   +<helpers/ui/GxEPDDisplay.cpp>
   +<helpers/ui/buzzer.cpp>

variants/thinknode_m1/target.h

@@ -3,7 +3,7 @@
 #define RADIOLIB_STATIC_ONLY 1
 #include <RadioLib.h>
 #include <helpers/radiolib/RadioLibWrappers.h>
-#include <helpers/nrf52/ThinkNodeM1Board.h>
+#include <ThinkNodeM1Board.h>
 #include <helpers/radiolib/CustomSX1262Wrapper.h>
 #include <helpers/AutoDiscoverRTCClock.h>
 #include <helpers/SensorManager.h>