xiao-nrf52 : initial support for meshcore

initial config for xiao_nrf52

repeater role for xiao-nrf52

xiao-nrf52 correction on bat voltage

xiao-nrf52 this file should not be here ...

src/helpers/nrf52/XiaoNrf52Board.cpp

@@ -0,0 +1,91 @@
+#include <Arduino.h>
+#include "XiaoNrf52Board.h"
+
+#include <bluefruit.h>
+#include <Wire.h>
+
+static BLEDfu bledfu;
+
+static void connect_callback(uint16_t conn_handle)
+{
+  (void)conn_handle;
+  MESH_DEBUG_PRINTLN("BLE client connected");
+}
+
+static void disconnect_callback(uint16_t conn_handle, uint8_t reason)
+{
+  (void)conn_handle;
+  (void)reason;
+
+  MESH_DEBUG_PRINTLN("BLE client disconnected");
+}
+
+void XiaoNrf52Board::begin() {
+  // for future use, sub-classes SHOULD call this from their begin()
+  startup_reason = BD_STARTUP_NORMAL;
+
+  pinMode(PIN_VBAT, INPUT);
+  pinMode(VBAT_ENABLE, OUTPUT);
+  digitalWrite(VBAT_ENABLE, HIGH);
+
+#if defined(PIN_WIRE_SDA) && defined(PIN_WIRE_SCL)
+  Wire.setPins(PIN_WIRE_SDA, PIN_WIRE_SCL);
+#endif
+
+  Wire.begin();
+
+#ifdef P_LORA_TX_LED
+  pinMode(P_LORA_TX_LED, OUTPUT);
+  digitalWrite(P_LORA_TX_LED, HIGH);
+#endif
+
+//  pinMode(SX126X_POWER_EN, OUTPUT);
+//  digitalWrite(SX126X_POWER_EN, HIGH);
+  delay(10);   // give sx1262 some time to power up
+}
+
+bool XiaoNrf52Board::startOTAUpdate(const char* id, char reply[]) {
+  // Config the peripheral connection with maximum bandwidth
+  // more SRAM required by SoftDevice
+  // Note: All config***() function must be called before begin()
+  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
+
+  Bluefruit.begin(1, 0);
+  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
+  Bluefruit.setTxPower(4);
+  // Set the BLE device name
+  Bluefruit.setName("XIAO_NRF52_OTA");
+
+  Bluefruit.Periph.setConnectCallback(connect_callback);
+  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
+
+  // To be consistent OTA DFU should be added first if it exists
+  bledfu.begin();
+
+  // Set up and start advertising
+  // Advertising packet
+  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+  Bluefruit.Advertising.addTxPower();
+  Bluefruit.Advertising.addName();
+
+  /* Start Advertising
+    - Enable auto advertising if disconnected
+    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
+    - Timeout for fast mode is 30 seconds
+    - Start(timeout) with timeout = 0 will advertise forever (until connected)
+
+    For recommended advertising interval
+    https://developer.apple.com/library/content/qa/qa1931/_index.html
+  */
+  Bluefruit.Advertising.restartOnDisconnect(true);
+  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
+  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
+  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds
+
+  strcpy(reply, "OK - started");
+  return true;
+
+
+  return false;
+}

src/helpers/nrf52/XiaoNrf52Board.h

@@ -0,0 +1,75 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+
+// LoRa radio module pins for Seeed Xiao-nrf52
+#ifdef SX1262_XIAO_S3_VARIANT
+  #define  P_LORA_DIO_1       D0
+  #define  P_LORA_BUSY        D1
+  #define  P_LORA_RESET       D2
+  #define  P_LORA_NSS         D3
+  #define  LORA_TX_BOOST_PIN  D4
+#else
+  #define  P_LORA_DIO_1       D1
+  #define  P_LORA_BUSY        D3
+  #define  P_LORA_RESET       D2
+  #define  P_LORA_NSS         D4
+  #define  LORA_TX_BOOST_PIN  D5
+#endif
+#define  P_LORA_SCLK        PIN_SPI_SCK
+#define  P_LORA_MISO        PIN_SPI_MISO
+#define  P_LORA_MOSI        PIN_SPI_MOSI
+//#define  SX126X_POWER_EN  37
+
+#define SX126X_DIO2_AS_RF_SWITCH  true
+#define SX126X_DIO3_TCXO_VOLTAGE   1.8
+
+
+class XiaoNrf52Board : public mesh::MainBoard {
+protected:
+  uint8_t startup_reason;
+
+public:
+  void begin();
+  uint8_t getStartupReason() const override { return startup_reason; }
+
+#if defined(P_LORA_TX_LED)
+  void onBeforeTransmit() override {
+    digitalWrite(P_LORA_TX_LED, LOW);   // turn TX LED on
+  }
+  void onAfterTransmit() override {
+    digitalWrite(P_LORA_TX_LED, HIGH);   // turn TX LED off
+  }
+#endif
+
+  uint16_t getBattMilliVolts() override {
+    // Please read befor going further ;)
+    // https://wiki.seeedstudio.com/XIAO_BLE#q3-what-are-the-considerations-when-using-xiao-nrf52840-sense-for-battery-charging
+
+    pinMode(BAT_NOT_CHARGING, INPUT);
+    if (digitalRead(BAT_NOT_CHARGING) == HIGH) {
+      int adcvalue = 0;
+      analogReadResolution(12);
+      analogReference(AR_INTERNAL_3_0);  
+      digitalWrite(VBAT_ENABLE, LOW);
+      delay(10);
+      adcvalue = analogRead(PIN_VBAT);
+      digitalWrite(VBAT_ENABLE, HIGH);
+      return (adcvalue * ADC_MULTIPLIER * AREF_VOLTAGE) / 4.096;
+    } else {
+      digitalWrite(VBAT_ENABLE, HIGH); // ensures high !
+      return 4200; // charging value
+    }
+  }
+
+  const char* getManufacturerName() const override {
+    return "Seeed Xiao-nrf52";
+  }
+
+  void reboot() override {
+    NVIC_SystemReset();
+  }
+
+  bool startOTAUpdate(const char* id, char reply[]) override;
+};