docs: sync CLI and payload docs with implementation

docs/cli_commands.md

@@ -53,7 +53,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 - `time <epoch_seconds>`
 
 **Parameters:**
-- `epoc_seconds`: Unix epoc time
+- `epoch_seconds`: Unix epoch time
 
 ---
 
@@ -63,6 +63,12 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
+### Send a zero-hop advert
+**Usage:**
+- `advert.zerohop`
+
+---
+
 ### Start an Over-The-Air (OTA) firmware update
 **Usage:**
 - `start ota`
@@ -136,7 +142,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
-### End capture of rx log to node sotrage
+### End capture of rx log to node storage
 **Usage:** `log stop`
 
 ---
@@ -200,7 +206,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 **Default:** Varies by board
 
-**Notes:** This setting only controls the power level of the LoRa chip. Some nodes have an additional power amplifier stage which increases the total output. Referr to the node's manual for the correct setting to use. **Setting a value too high may violate the laws in your country.**
+**Notes:** This setting only controls the power level of the LoRa chip. Some nodes have an additional power amplifier stage which increases the total output. Refer to the node's manual for the correct setting to use. **Setting a value too high may violate the laws in your country.**
 
 ---
 
@@ -230,6 +236,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 **Default:** `869.525`
 
 **Note:** Requires reboot to apply
+**Serial Only:** `set freq <frequency>`
 
 ### System
 
@@ -287,7 +294,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 **Serial Only:**
 - `get prv.key`: Yes
-- `set prv.key`: No
+- `set prv.key`: Yes
 
 **Note:** Requires reboot to take effect after setting
 
@@ -295,16 +302,16 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 #### Change this node's admin password
 **Usage:**
-- `password <password>`
+- `password <new_password>`
 
 **Parameters:**
-- `password`: Admin password
+- `new_password`: New admin password
 
 **Set by build flag:** `ADMIN_PASSWORD`
 
 **Default:** `password`
 
-**Note:** Echoed back for confirmation
+**Note:** Command reply echoes the updated password for confirmation.
 
 **Note:** Any node using this password will be added to the admin ACL list.
 
@@ -354,13 +361,25 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
+#### View this node's public key
+**Usage:** `get public.key`
+
+---
+
+#### View this node's configured role
+**Usage:** `get role`
+
+---
+
 #### View or change this node's power saving flag (Repeater Only)
 **Usage:**
-- `powersaving <state>`
 - `powersaving`
+- `powersaving on`
+- `powersaving off`
 
 **Parameters:** 
-- `state`: `on`|`off` 
+- `on`: enable power saving
+- `off`: disable power saving
 
 **Default:** `on`
 
@@ -769,7 +788,7 @@ region save
 - `gps advert <policy>`
 
 **Parameters:** 
-- `policy`: `none`|`shared`|`prefs` 
+- `policy`: `none`|`share`|`prefs` 
   - `none`: don't include location in adverts
   - `share`: share gps location (from SensorManager)
   - `prefs`: location stored in node's lat and lon settings
@@ -803,6 +822,11 @@ region save
 
 ### Bridge (When bridge support is compiled in)
 
+#### View the compiled bridge type
+**Usage:** `get bridge.type`
+
+---
+
 #### View or change the bridge enabled flag
 **Usage:**
 - `get bridge.enabled`
@@ -840,10 +864,10 @@ region save
 
 **Parameters:**
 - `source`: 
-  - `rx`: bridges received packets
-  - `tx`: bridges transmitted packets
+  - `logRx`: bridges received packets
+  - `logTx`: bridges transmitted packets
 
-**Default:** `tx`
+**Default:** `logTx`
 
 ---
 
@@ -875,8 +899,39 @@ region save
 - `set bridge.secret <secret>`
 
 **Parameters:**
-- `secret`: 16-character encryption secret
+- `secret`: ESP-NOW bridge secret, up to 15 characters
 
 **Default:** Varies by board
 
 ---
+
+#### View the bootloader version (nRF52 only)
+**Usage:** `get bootloader.ver`
+
+---
+
+#### View power management support
+**Usage:** `get pwrmgt.support`
+
+---
+
+#### View the current power source
+**Usage:** `get pwrmgt.source`
+
+**Note:** Returns an error on boards without power management support.
+
+---
+
+#### View the boot reset and shutdown reasons
+**Usage:** `get pwrmgt.bootreason`
+
+**Note:** Returns an error on boards without power management support.
+
+---
+
+#### View the boot voltage
+**Usage:** `get pwrmgt.bootmv`
+
+**Note:** Returns an error on boards without power management support.
+
+---