Merge pull request #90 from oltaco/faketec-support

Faketec support

src/helpers/nrf52/faketecBoard.cpp

@@ -0,0 +1,63 @@
+#include <Arduino.h>
+#include "faketecBoard.h"
+
+#include <bluefruit.h>
+#include <Wire.h>
+
+static BLEDfu bledfu;
+
+static void connect_callback(uint16_t conn_handle)
+{
+    (void)conn_handle;
+    MESH_DEBUG_PRINTLN("BLE client connected");
+}
+
+static void disconnect_callback(uint16_t conn_handle, uint8_t reason)
+{
+    (void)conn_handle;
+    (void)reason;
+
+    MESH_DEBUG_PRINTLN("BLE client disconnected");
+}
+
+bool faketecBoard::startOTAUpdate() {
+    // Config the peripheral connection with maximum bandwidth
+    // more SRAM required by SoftDevice
+    // Note: All config***() function must be called before begin()
+    Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+    Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
+
+    Bluefruit.begin(1, 0);
+    // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
+    Bluefruit.setTxPower(4);
+    // Set the BLE device name
+    Bluefruit.setName("Faketec_OTA");
+
+    Bluefruit.Periph.setConnectCallback(connect_callback);
+    Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
+
+    // To be consistent OTA DFU should be added first if it exists
+    bledfu.begin();
+
+    // Set up and start advertising
+    // Advertising packet
+    Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+    Bluefruit.Advertising.addTxPower();
+    Bluefruit.Advertising.addName();
+
+    /* Start Advertising
+     - Enable auto advertising if disconnected
+     - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
+     - Timeout for fast mode is 30 seconds
+     - Start(timeout) with timeout = 0 will advertise forever (until connected)
+
+     For recommended advertising interval
+     https://developer.apple.com/library/content/qa/qa1931/_index.html
+    */
+    Bluefruit.Advertising.restartOnDisconnect(true);
+    Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
+    Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
+    Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds
+
+  return true;
+}

src/helpers/nrf52/faketecBoard.h

@@ -0,0 +1,69 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+#include <Wire.h>
+
+#define P_LORA_NSS 13 //P1.13 45
+#define P_LORA_DIO_1 11 //P0.10 10
+#define P_LORA_RESET 10 //P0.09 9
+#define P_LORA_BUSY  16 //P0.29 29
+#define P_LORA_MISO  15 //P0.02 2
+#define P_LORA_SCLK  12 //P1.11 43
+#define P_LORA_MOSI  14 //P1.15 47
+#define SX126X_POWER_EN 21 //P0.13 13
+#define SX126X_RXEN 2 //P0.17
+#define SX126X_TXEN RADIOLIB_NC
+#define SX126X_DIO2_AS_RF_SWITCH  true
+#define SX126X_DIO3_TCXO_VOLTAGE (1.8f)
+
+#define  PIN_VBAT_READ 17
+#define  ADC_MULTIPLIER   (1.815f) // dependent on voltage divider resistors. TODO: more accurate battery tracking
+
+class faketecBoard : public mesh::MainBoard {
+protected:
+  uint8_t startup_reason;
+
+public:
+  void begin() {
+    // for future use, sub-classes SHOULD call this from their begin()
+    startup_reason = BD_STARTUP_NORMAL;
+
+    pinMode(PIN_VBAT_READ, INPUT);
+
+    #if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
+      Wire.begin(PIN_BOARD_SDA, PIN_BOARD_SCL);
+    #else
+      Wire.begin();
+    #endif
+
+    pinMode(SX126X_POWER_EN, OUTPUT);
+    digitalWrite(SX126X_POWER_EN, HIGH);
+    delay(10);   // give sx1262 some time to power up
+  }
+
+  uint8_t getStartupReason() const override { return startup_reason; }
+
+  #define BATTERY_SAMPLES 8
+
+  uint16_t getBattMilliVolts() override {
+    analogReadResolution(12);
+
+    uint32_t raw = 0;
+    for (int i = 0; i < BATTERY_SAMPLES; i++) {
+      raw += analogRead(PIN_VBAT_READ);
+    }
+    raw = raw / BATTERY_SAMPLES;
+    return (ADC_MULTIPLIER * raw);
+  }
+
+  const char* getManufacturerName() const override {
+    return "Faketec DIY";
+  }
+
+  void reboot() override {
+    NVIC_SystemReset();
+  }
+
+  bool startOTAUpdate() override;
+};