mirror of
https://github.com/g4klx/MMDVM_HS.git
synced 2025-12-06 07:02:00 +01:00
115 lines
3.3 KiB
C
115 lines
3.3 KiB
C
/*
|
|
* Copyright (C) 2017,2018,2019 by Andy Uribe CA6JAU, Florian Wolters DF2ET
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
#if !defined(CONFIG_H)
|
|
#define CONFIG_H
|
|
|
|
// Select one board (STM32F103 based boards)
|
|
// 1) ZUMspot RPi or ZUMspot USB:
|
|
// #define ZUMSPOT_ADF7021
|
|
// 2) Libre Kit board or any homebrew hotspot with modified RF7021SE and Blue Pill STM32F103:
|
|
// #define LIBRE_KIT_ADF7021
|
|
// 3) MMDVM_HS_Hat revisions 1.1, 1.2 and 1.4 (DB9MAT & DF2ET)
|
|
// #define MMDVM_HS_HAT_REV12
|
|
// 4) MMDVM_HS_Dual_Hat revisions 1.0 (DB9MAT & DF2ET & DO7EN)
|
|
#define MMDVM_HS_DUAL_HAT_REV10
|
|
// 5) Nano hotSPOT (BI7JTA)
|
|
// #define NANO_HOTSPOT
|
|
// 6) NanoDV NPi or USB revisions 1.0 (BG4TGO & BG5HHP)
|
|
// #define NANO_DV_REV10
|
|
// 7) D2RG MMDVM_HS RPi (BG3MDO, VE2GZI, CA6JAU)
|
|
// #define D2RG_MMDVM_HS
|
|
|
|
// Enable ADF7021 support:
|
|
#define ENABLE_ADF7021
|
|
|
|
// Enable full duplex support with dual ADF7021 (valid for homebrew hotspots only):
|
|
#define DUPLEX
|
|
|
|
// TCXO of the ADF7021
|
|
// For 14.7456 MHz:
|
|
#define ADF7021_14_7456
|
|
// For 12.2880 MHz:
|
|
// #define ADF7021_12_2880
|
|
|
|
// Configure receiver gain for ADF7021
|
|
// AGC automatic, default settings:
|
|
#define AD7021_GAIN_AUTO
|
|
// AGC automatic with high LNA linearity:
|
|
// #define AD7021_GAIN_AUTO_LIN
|
|
// AGC OFF, lowest gain:
|
|
// #define AD7021_GAIN_LOW
|
|
// AGC OFF, highest gain:
|
|
// #define AD7021_GAIN_HIGH
|
|
|
|
// Host communication selection:
|
|
#define STM32_USART1_HOST
|
|
// #define STM32_USB_HOST
|
|
// #define STM32_I2C_HOST
|
|
|
|
// I2C host address:
|
|
#define I2C_ADDR 0x22
|
|
|
|
// Enable mode detection:
|
|
#define ENABLE_SCAN_MODE
|
|
|
|
// Send RSSI value:
|
|
#define SEND_RSSI_DATA
|
|
|
|
// Enable Nextion LCD serial port repeater on USART2 (ZUMspot Libre Kit and ZUMspot RPi):
|
|
#define SERIAL_REPEATER
|
|
#define SERIAL_REPEATER_BAUD 9600
|
|
|
|
// Enable Nextion LCD serial port repeater on USART1 (Do not use with STM32_USART1_HOST enabled):
|
|
// #define SERIAL_REPEATER_USART1
|
|
|
|
// Enable P25 Wide modulation:
|
|
// #define ENABLE_P25_WIDE
|
|
|
|
// Disable mode LEDs blink during scan mode:
|
|
// #define QUIET_MODE_LEDS
|
|
|
|
// Engage a constant or descreet Service LED mode once repeater is running
|
|
// #define CONSTANT_SRV_LED
|
|
// #define CONSTANT_SRV_LED_INVERTED
|
|
// #define DISCREET_SRV_LED
|
|
// #define DISCREET_SRV_LED_INVERTED
|
|
|
|
// Use the YSF and P25 LEDs for NXDN
|
|
// #define USE_ALTERNATE_NXDN_LEDS
|
|
|
|
// Use the D-Star and DMR LEDs for POCSAG
|
|
#define USE_ALTERNATE_POCSAG_LEDS
|
|
|
|
// Enable for RPi 3B+, USB mode
|
|
// #define LONG_USB_RESET
|
|
|
|
// Enable modem debug messages
|
|
// #define ENABLE_DEBUG
|
|
|
|
// Disable frequency bands check
|
|
// #define DISABLE_FREQ_CHECK
|
|
|
|
// Disable frequency restrictions (satellite, ISS, etc)
|
|
// #define DISABLE_FREQ_BAN
|
|
|
|
// Enable UDID feature
|
|
#define ENABLE_UDID
|
|
|
|
#endif
|